Lincoln Electric Welder 248HO User Manual

US-CW223  
Date:  
11/1/06  
MSDS No.:  
Lincore 410  
All  
Trade Name:  
Sizes:  
Supersedes:  
5/1/01  
M A T E R I A L S A F E T Y D A T A S H E E T  
For Welding Consumables and Related Products  
Conforms to Hazard Communication Standard 29CFR 1910.1200 Rev. October 1988  
SECTION I - IDENTIFICATION  
Manufacturer/  
Supplier:  
The Lincoln Electric Company  
22801 St. Clair Avenue  
Cleveland, OH 44117-1199  
(216) 481-8100  
Cored Electrode  
Product Type:  
Classification:  
None  
SECTION II - HAZARDOUS MATERIAL (1)  
I M P O R T A N T !  
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal  
use of this product are covered by Section V; see it for industrial hygiene information.  
CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.  
(1) The term “hazardous” in “Hazardous Materials” should be interpreted as a term required and defined in the Hazards Communication  
Standard and does not necessarily imply the existence of any hazard. All materials are listed on the TSCA inventory.  
TLV  
PEL  
Ingredients:  
CAS No.  
7440-47-3  
7439-89-6  
1309-48-4  
7439-96-5  
1332-58-7  
1344-28-1  
7440-02-0  
7429-90-5  
7789-75-5  
7439-95-4  
7440-21-3  
1333-86-4  
1344-09-8  
Wt.%  
15  
< 5  
1
0.5  
mg/m3  
0.5(b)  
10*  
10  
mg/m3  
1.0(b)  
10*  
15  
Chromium and chromium alloys or compounds (as Cr)*****  
Iron  
Magnesite  
Manganese and/or manganese alloys and compounds (as Mn)*****  
Mineral silicates  
Aluminum oxide and/or Bauxite*****  
Nickel (metal)*****  
Aluminum and/or aluminum alloys (as Al)*****  
Fluorides (as F)  
Magnesium and/or magnesium alloys and compounds (as Mg)  
Silicon and/or silicon alloys and compounds (as Si)  
Carbon black  
0.2  
5**  
10  
1.0(c)  
5**  
10  
0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
1.5  
1
10  
15  
2.5  
2.5  
10*  
10*  
3.5  
10*  
10*  
3.5  
Silicates and other binders  
10*  
10*  
Carbon steel tube  
7439-89-6  
80  
10*  
10*  
Supplemental Information: (*) Not listed. Nuisance value maximum (b) The OSHA PEL for chromium (VI) is 5 micrograms  
is 10 milligrams per cubic meter. PEL value for iron oxide is 10 milligrams per  
cubic meter. TLV value for iron oxide is 5 milligrams per cubic meter.  
(0.005 milligrams) per cubic meter. The TLV for water  
soluble chromium (VI) is 0.05 milligrams per cubic meter  
and the TLV for insoluble chromium (VI) is 0.01  
milligrams per cubic meter.  
(**)  
As respirable dust.  
(*****) Subject to the reporting requirements of Sections 311, 312, and 313 of (c) Values are for manganese fume. STEL (Short Term  
the Emergency Planning and Community Right-to-Know Act of 1986  
and of 40CFR 370 and 372.  
Exposure Limit) is 3.0 milligrams per cubic meter.  
PEL is 5.0 milligrams per cubic meter (ceiling value).  
SECTION III - HAZARD DATA  
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section VI. Product is inert, no  
special handling or spill procedures required. Not regulated by DOT.  
Rev 11/06b  
(CONTINUED ON SIDE TWO)  
 

KTM Motorcycle EXC 200 EXC User Manual
Legacy Car Audio Car Video System L7HM User Manual
Leica Insulin Pen NCL L INSULIN User Manual
LG Electronics Air Conditioner EN 61000 2 User Manual
LOREX Technology Switch CVA6933 User Manual
Magic Chef Coffeemaker EWCM11TS12 User Manual
Makita Grinder GA5020 User Manual
Maytag Clothes Dryer MEDZ400TQ1 User Manual
Metz Flat Panel Television 42TM92 User Manual
Meyer Sound Portable Speaker MICA User Manual