Lincoln Electric Welder 81K2A75 H User Manual

US-CW751  
12/17/2007  
Date:  
MSDS No.:  
UltraCore 81K2A75-H  
All  
Trade Name:  
Sizes:  
9/24/2007  
Supersedes:  
M A T E R I A L S A F E T Y D A T A S H E E T  
For Welding Consumables and Related Products  
Conforms to Hazard Communication Standard 29CFR 1910.1200 Rev. October 1988  
SECTION I - IDENTIFICATION  
Manufacturer/  
Supplier:  
The Lincoln Electric Company  
22801 St. Clair Avenue  
Cleveland, OH 44117-1199  
(216) 481-8100  
Flux Cored Electrode  
Product Type:  
AWS: E81T1-K2MJ-H4  
Classification:  
SECTION II - HAZARDOUS MATERIAL (1)  
I M P O R T A N T !  
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal  
use of this product are covered by Section V; see it for industrial hygiene information.  
CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.  
(1) The term “hazardous” in “Hazardous Materials” should be interpreted as a term required and defined in the Hazards Communication  
Standard and does not necessarily imply the existence of any hazard. All materials are listed on the TSCA inventory.  
TLV  
PEL  
Ingredients:  
CAS No.  
13463-67-7  
7440-02-0  
7439-96-5  
7439-89-6  
7439-95-4  
1332-58-7  
7789-75-5  
7440-21-3  
12719-90-3  
11108-67-1  
Wt.%  
10  
< 5  
< 5  
1
mg/m3  
10  
mg/m3  
15  
Titanium dioxides  
Nickel (metal)*****  
Manganese and/or manganese alloys and compounds (as Mn)*****  
Iron  
Magnesium and/or magnesium alloys and compounds (as Mg)  
Mineral silicates  
Fluorides (as F)  
Silicon and/or silicon alloys and compounds (as Si)  
Titanium and/or titanium alloys (as Ti)  
Boron alloys (as B)  
1.5  
1
0.2  
5 (c)  
10*  
10*  
5**  
2.5  
10*  
10*  
5**  
2.5  
0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
< 0.5  
10*  
10*  
10*  
10*  
10*  
10*  
Carbon steel tube  
85  
7439-89-6  
10*  
10*  
Supplemental Information:  
(*)  
Not listed. Nuisance value maximum is 10 milligrams per cubic meter. (c)  
PEL value for iron oxide is 10 milligrams per cubic meter. TLV value  
for iron oxide is 5 milligrams per cubic meter.  
Value is for manganese fume. Present PEL is 5  
milligrams per cubic meter (ceiling value). Values  
proposed by OSHA in 1989 were 1.0 milligrams per  
cubic meter TWA and 3.0 milligrams per cubic meter  
STEL (Short Term Exposure Limit).  
(**)  
As respirable dust.  
(*****) Subject to the reporting requirements of Sections 311, 312, and 313 of  
the Emergency Planning and Community Right-to-Know Act of 1986  
and of 40CFR 370 and 372.  
SECTION III - HAZARD DATA  
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See Z49.1 referenced in Section VI.  
Product is inert, no special handling or spill procedures required. Not regulated by DOT.  
Rev 9/07  
(CONTINUED ON SIDE TWO)  
 

Legacy Car Audio Car Stereo System LCA Series User Manual
Lennox Hearth Indoor Fireplace EBVI25 User Manual
LevelOne Switch GSW 1601TX User Manual
Lightolier Indoor Furnishings T7032 User Manual
Lightolier Work Light LLC2 User Manual
LOREX Technology Computer Monitor L17LD420 User Manual
LST Network Card LIF64 1 User Manual
Magnadyne Headphones Digital Headphones User Manual
Makita Car Video System BO4555 User Manual
Memorex MP3 Player MPD8610 User Manual